I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi
I need to connect to perticular central and i know the central MAC address. So i am using whitelisting in peripheral.
I made below changes in my code in ble_app_uart...
I am trying to use the gzp_dynamic_pairing example in SDK version 16 with Segger Embedded Studio and the PCA10040 dev board. There is no project for SES so I copied what I...
Hi,
I am working on nRF5_SDK_17.0.0_9d13099\examples\peripheral\uart project.
How can I increase the UART buffer? like if I have to receive 100+ bytes data how can I read...
I am using a nRF9160 DK. I'm using a Windows 10 system and setup the SDK using nRF Connect.
I've started to experiment with the serial_lte_modem project -- version 1.3.1...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html links to two pages which cannot be found: https://infocenter.nordicsemi...
Hi,
I am able to transfer data from my custom peripheral device with nRF52840, but data is moving much slower than it should.
I am writing 244 bytes into NUS within...
Hi,
I am trying to use Cbor library provided the SDK version 1.3.0, I have added the module in my prj.conf file, however the documentation (at the top of cborencoder.c)...
This is the name that is advertised when the device is in DFU bootloader mode.
I've copied the bootloader_secure_ble from /examples/dfu/ but I cannot find where to change...
Hi every body,
My system was able to wake up on gpio on dev kit but after adjusting pin , my custom board is not able to wake up.
I'm in debug mode, it was also working...
Hello,
I am trying to send a single adv packet when a certain condition in the application is met. To do this I am calling ADV_start for the initial adv packet and then...
These questions are in the context of using an nRF52840 in a serialization application. But I don't believe this will impact the information I am trying to understand. The...
I want to program the firmware into a nrf52840 on our custom board to be the NCP and do the DFU over thread. I can not use the DK board and have the nrfutil load the firmware...
Hi,
Our application uses MQTT over TLS to talk to a MQTT broker.
The MQTT APIs used are like in the 'mqtt_simple' sample code.
When mqtt_connect is called with invalid...
Hi,
I'm designing an application using SEGGER Studio for the nRF52832. I have based my application on the template peripheral example.
What I want to do is to trigger...
Hi--
I tried to implement an internally managed RTC using the app timer library, but came to find the error on that is too much for an RTC (~25 min lost over a few days...
