I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
[EDIT] The solution is posted in one of my replies.
I'd like to set up a programming and test station for the nRF52832. Segger JLink tools work fine in Windows, but I...
Good day Nordic,
I am starting to work over the ble_uart_central example, this is a project that uses bsp_event_handler to issue the events from buttons, but I cannot...
I am new to Nordic and i am using nRF52840 microcontroller, - SDK 15.2.0 - s140
When i program the microcontroller it gives me error message that my flash storage is full...
Hi,
I am using nRF5_SDK_15.3.0_59ac345 for nRF52840 DK. I am running the sdk example "nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_sensor" on nrf52840. When I am opened...
I'm currently trying to build and run the bluetooth mouse sample code on my nRF9160 DK, but I'm ecountering problems during the build process.
Shortly after hitting the...
I am having some trouble with sending messages using MQTT on nRF9160DK. What I ultimately want to to is read UART and send whatever I receive to an MQTT broker. When running...
I am trying to use sd_ble_gatts_hvx function to send custom data through BLE. I found out that for the data I am sending the function takes a lot of time to send data which...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
Hi
I have some question about DFU for Mesh3.10.
1.How to update Softdevice or Bootloader?such as I'm going to update SD from version 6.0.0 to 6.1.0.
2.Because my firmware...
