Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
Hi
I have some question about DFU for Mesh3.10.
1.How to update Softdevice or Bootloader?such as I'm going to update SD from version 6.0.0 to 6.1.0.
2.Because my firmware...
I am trying to port pc-ble-driver-py to soft device version 6.1. I have made changes to python code to take care of changed API signatures, new constants etc.
When testing...
Hi,
I am using nrf52832, in the ble_app_uart_c example, i want to use rc source as a lfclk,
i changed the following parameters in the sdk_config.h:
NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I have developed a custom PCB using nRF52832. It's meant to work as an ibeacon currently and consequently works in a non-connectable, advertising only mode. I will...
Hi,
I am trying to use GPIOTE_PIN_HANDLER in the master nrf52. What is the correct way to read data from slave?
Slave device is sending data using nrfx_twis_tx_prepare...
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using app_timer_create() to create low power...
Good morning developers, I want to ask you what is the maximum transfer speed (Kbps) achieved between the chip nrf52840 (peripheral) and a smartphone (central). If anyone...
As I reviewed other post, there are many similar topic.
Thus, I would like to know whether there is new tool for the application recently.
Does Nordic have development...
