I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I am using SDK12.3 and have problem with garbage collection (FDS module).
My apllication depends on timeslot, so that FDS is supposed to run together with Bluetooth...
Hi
I am writing ANT+ device on pStorage and want to read back from memory during ANT+ stack init. I am trying to change the Device name on this snippet
No luck so...
Hi,
I'm working on the ble_att_mtu_throughput example code on nrf52840(peripheral) & nrf52832(central) . SPI data is transmitting from TI(slave) board to nrf52840(master...
Hi there! I am developing a device with the nRF52810 that requires the following:
Receive audio over BLE
Store audio in memory
Playback audio on command
Would...
SDK 15.2 API 6.10 SES custom board
I am trying to get DFU to work and it is not seeming to work right.
I am trying to engage DFU mode by holding in button on board for...
Dear DevZonee's
Im trying to esablish a BLE connection using the following configuration of the peer-manager:
* LESC
* Just Works -> IO-Caps none (0x03)
If i run...
Hello
I am using SDK12.3 on nRF51822 chip using Keil V5 on windows 10.
I am using experimental_ble_app_buttonless_dfu example and bootloader_secure example.
They both...
Hello!
SDK 15.3
If I build secure_bootloader example project using Segger Embedded Studio it works, I can see it nRF connect.
If I build it using armgcc it does not...
Is there any actual difference between "Fast Advertising", and "Slow Advertising" - or is it just a way to easily specify two different sets of timing parameters?
The question...
Hi,
I'm having problems with the bootloader in SDK 15.2. I'm using an NRF52840, I don't know if the CryptoCell is giving me issues.
The DFU fails when checking the FW...
Hi All,
Sorry if this is a simple question, but I can't seem to find an example where the device is programmed as both RX and TX. (The examples have either one or the other...
Hello,
I am developing application which allows multiple central devices (phones) connect to a single peripheral device (custom board with nRF52840). I took example from...
We are under development on our custom board. then we suddenly were able to flashing the firmware, hex files onto our target board. SES showed the popup message such as "...
Hello,
I am unable to flash target board using my nrf52840 Dev board. I have two dev boards and I am able to flash the target with the other dev board.
The target board...
To what values should I set the PWMCON register to so that the PWM0 and PWM1 frequency is output at 20Khz with duty cycle varying between 1 to 2ms. Now specifically I am asking...
