before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi Team,
May I know your kind advice on the following issue when I tried to Open the SDK project in SES. I have seen some discussions on line but none of them works for...
I'm trying to migrate from SDK12 to SDK15, but my code always crashes at advertising_init() and goes to NRF_BREAKPOINT_COND. Even when I directly use the example from the...
I tried searching for this response but cant find exact answer
SDK15.2 and API6.1
I am trying to have an advertiser but would like to put it in some sleep mode and advertise...
There are a few pins I want to use but are already assigned to MCU interface UART or buttons like p0.05 to p0.08 and p0.11 to p0.16 on the nRF52840 DK. I’m wondering if it...
Hi,
We are encountering a problem when we try to avail Nordic UART service (NUS) and Mesh service in one application. The problem statement is that after Provisioning, when...
Dear Team,
We are working on nRF52832 BLE MCU. SDK version = 15.0.0. SOFTDEVICE version = 6.0.0. IDE = segger embedded studio.
In our application we required software...
Hi,
I have read this thread Notification_Loss but could not understand my problem.
On peripheral side, I am making sure that error events are properly handled while doing...
Hi,
I'm working on an application for the nRF9160 using the nRF Connect SDK. I want to integrate this app into our build system and thus would like to be able to build...
Hi,
we have to stick to SDK 14.2 because our project is close to finish and we use C++ which is not good supported be SDK <15 due to the macros.
But still we would like...
Hello, I am trying to adapt open thread coap example to use with the PCA10059/NRF52840 Dongle board. I am using segger IDE. I adapted the CLI to use the USB like in the thread_cli_usb_bootloader...
Hi all,
i want to read the power (WATTS) value and send it to ble. i have attached datasheet also. i want to know how to trasmit COMMAND e.g 0x58 through UART. any api...
SDK 15.2 SD API 6.1 SES I am trying to get my system to work on a DFU system. In order to do it i need to have a secure bootloader.
using the secure bootloader in the example...
Is there a way to configure the nRF51822 to support writewithoutResponse? I'm using the Adafruit Feather 32u4 with the nRF51822 ble chip. My iOS app works fine with the older...
Hi
I plan to use nRF52832 based nodes with an accelerometer sensor which generates data at a rate of 468 bytes per second. For evaluation, I have two nRF-52 DK evaluation...
1. I read the Configuring DFU over Mesh & nrfutil User Guide , but still do not know how to test this example.
2.is we must need 2 devices, A connenct to PC for nrfutil...
