I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
I am trying to detect when mtu has been successfully negotiated through the ble_evt_handler function, which is passed into NRF_SDH_BLE_OBSERVER as shown below:
// Register...
Hi - I'm trying to program the Thingy52 using my nRF52840 DK and Macbook Pro. I've got the Thingy connected to the DK via the 10-pin cable. The first time I ran nrfjprog on...
Hi there!
I have migrated ble_mpu_simple from sdk14.2 to sdk 15.2.
I use Keil uVision to test "nRF5_SDK_15.2.0_9412b96\examples\nRF5-mpu-examples-master\nrf5_ble_mpu_simple...
Hello,
Let me start off by saying that in our use case we are transferring large amounts of data (megabytes) through BLE. This works fine on iPhone 6s+, iPhone SE, iPhone...
Hi,
We're looking for a Bluetooth chipset / module for a Android Pad hardware.
Given that Android 8.0 BlueDroid stack requires Bluetooth chip support HCI commands, is...
Dear all we are using nrf52810(48pin).we did not find exact solution about how many i2c and spi available for that.in which pin we have to connect i2c device and SPI devices...
Good day!
How can I calculate the maximum throughput for BLE Mesh running on the nRF52832 and the S132 without packet loss in ideal conditions?
I have tested throughput...
I notice that for everything related to a BLE connection in the nRF code, there is a "connection handle". Usually, the handle is zero. When is the connection handle NOT zero...
I have successfully worked out the Light Switch Example in the nRF Mesh SDK v3.0.0 using nRF52 DKs. I used the nRF Mesh app for provisioning. I want to know what is the next...
Hi
I am using nrf51822 AC custom board and willing to program over dfu.
For dfu service setting I referred following links. Only change I did in pca10028 library because...
Hello, I'm working with the pca10040e version (s112) of the nordic UART template example. I want to read 20 values from the SAADC, average them, then take a TEMP reading,...
