Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
Hi all,
I like build a smartwatch-like device that can receive notifications from my android phone. The bluetooth device has a oled screen and displays what notification...
I need to turn on and off one pin around every 100 us. Time between must be 1 cycle (couple of ns) and can't be interrupted at any circumstances.
Without a softdevice I disable...
Hi All,
I am a beginner in nrf52.
I need to get the client device address in ble_app_hrs_central, because I have more than one devices connected.
There is a hrs_c_evt_handler...
After spending half a day on this solution, I found out it wasn't really a solution - it devolved back to the same issue after trying to connect - please advise!
Description...
I'm trying to connect to a ST LSM6DS3 via SPI on the Nordic chip. I have used SPI on Nordic with other peripherals but couldn't seem to get it to work with this ST chip. Eventually...
I'm having some issues getting any of the provided experimental Thread examples to compile with IAR version 8.11.2. I'm using an nRF52840-PDK with the SDK for Thread version...
Hello,
I wonder how power failure comparator works at VDD 2.1V.
If VDD goes down to 2.1V, and I set POFCON enabled at 2.1V threshold, then does POFWARN work?
How 2.1V...
Hi,
I am working on testing this modification on the ble_hrs example.
The idea is to send data sequentially as notifications.
However, BLE_EVT_TX_COMPLETE seems to...
Good morning
I use the fds function to store and read data in flash memory.
FDS_SUCCES is not returned by the fds_record_find function when reading data, so the read function...
Currently developing on NRF52 sdk12
I want to be able to show time stamp minutes:seconds:miliseconds on my RTT viewer, when I print my data out from the uC. Any hits on...
hello
i am using nrf52840, with BME280, i have external pullup 10k resistor.
how i can disable the internal pullup resistor.
i am using this sample code.
github.com...
