Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello Nordic!
This question is a follow-up on this topic , where it is suggested to keep track of BLE_GAP_EVT_CONNECTED and BLE_GAP_EVT_TIMEOUT events in order to know...
Hi, Nordic Forum!
I'm developing a product that relies heavily on the TWI in master mode. I was using SDK 11.0 and everything was working well.
I decided to port to...
I want to use another MCU(MT7688 run OpenWRT) as a upper monitor to DFU the nrf52832,But you know,the way of serial download for nrf52832 is use nrfutil with command that...
Hi There,
We are having an issue reading data from the ble_gatts_evt_rw_authorize_request_t.request.write.data buffer. We are writing the data to the characteristic using...
I need to receive both UART Service data and HRS service data on the app.
Currently I have seen on Nordik Connect app , both the services can be found and can connect and...
So we have the Arduino 101 board talking to a heart rate sensor MAX30100. When we run the nrf connect app on android it is able to connect to the sensor with no issues. When...
Sporadic program restart from main.
I suppose, it is hardfault exception. How can I catch it?
Check pls my memory settings.
ROM: start- 0x1c000 size 0x23000
RAM: start...
Im implementing an application which uses the s132 SD for BLE communication and the mesh implementation described at nRF51-ble-bcast-mesh. I need to have encrypted and authenticated...
Hi Forum,
I'm using SDK12 without ble. (peripherals/uart)
so, I can't pstorage or fstorage.
I want to write 4 bytes without erasing a page. And I want to update a value...
Hi. I'm using nRF52832, SDK13.0.0, S132.
When I make bootloader, I should make *.setting file for application.
Do i need *.setting file when I update just application...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
Hello,
I intended to implement an application without OS. Due to safety concerns I would like to have two call stacks : one for softdevice using MSP and the other for my...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
