If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Keil uV5, nRF51822, TWI hardware version
I'm trying to use twi_hw_master.c and I have made one simple change to define the CLOCK and DATA pins to 1U and 2U for my target...
From reading the product specification and the reference manual, it appears that there is no accessable DMA controller. and since there is no EASY DMA for uart, how would...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including nrf_delay.h compiling with gcc:
Nordic/nRF51_SDK_9.0...
I have another problem ，when i debug s130 demo by jtag，set free run，the software running OK
，but when i set a breakpoint or stop running，then free run again，the software...
I run a laptop which previously ran this fine on Windows 7 x64. I now run Windows 10 x64.
I cleaned out j-link, nrfgo studio, libusb etc and reinstalled nRFgo Studio again...
I know that it is possible to make 4 PWM outputs, but I need to generate 5. I will be using SoftDevice 110 and BLE. Is there any possible way to generate a 5th PWM output...
Hi,
I need to interface a LED driver (PCA9632) using TWI.
In the TWI APIs I can't see any way to pass the slave address to the TWI instance. Speaking about the nrf_drv_twi_init...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi, I have an nRF8001 on a Red Bear Lab BLE shield mounted on an Arduino Uno. I'm using BLE to trigger the execution of potentially long running (well, a few seconds anyway...
Hi,
I've done a fair amount with the NRF51822 and Keil on Windows but decided it was time to switch to my native Mac instead of the VM!
Reading all the guides around...
Hello everyone,
I'm a beginner and i'm trying to debug a nRF51422 BLE project.
The SoC is supposed to wait for commands from a STM32 in order to execute some functions...
Hello,
I'm a newbie in this area, and I'm trying to program NRF51822 QFAA on a custom board according to the given tutorial for a dual bank bootloader ( devzone.nordicsemi...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
