Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
from Keil uVision I need to debug/program nrf51822 in my application which uses 1.8 V. I guess nrf51 DK is not capable of doing this (it supports only 3 V targets). What...
Hi,
I have a reset issue when trying to set a delay greater or equal to 100 milliseconds using nrf_delay_ms(...). This only happens if I start my app timers (app_timer_start...
Hi,
I am trying to generate a 128Hz sine wave using the nrf_pwm library . First I tried this with SD110 enabled but ran into some problems that turned out to be a known...
Hi,
I'm going through the errata and a few of them look serious that the developer kit might be useless for some of us if we want to use it for any realistic testing (I...
I am trying to add a static passkey to my peripheral and protect from MITM. I tried the example nRF51-ble-app-uart-static-passkey but it doesn't seem to work correctly.
...
Hi,
I am new to nordic n51822, i have implemented adc and timer independently.
Now, what i want to do is read the adc values on a specific time when the timer overflows...
Received my nRF52 preview board yesterday and have been battling to get my S130 based nRF51 code running on it with the S132 soft device (the code is here: github.com/......
The codes i am using is
nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral and nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_peripheral\ble_app_hrs
From the peripheral...
Just getting started with the PCA10001. I can compile if I select the device nrf51822_xxaa_s110, but when I load it tells me "can't load flash device description".
It subsequently...
I have take the basic ble_app_hrs_with_timeslot and modified it to calculate the timing of subsequent calls to the timeslot START event.
Specifically,
take note...
Hello,
I'm trying to get the new SDK up and running on my OSX machine. I would like to make the blinky example work on my PCA10003. So, I copied the blinky/pca10028 folder...
Hello, Do you guys know if it is possible to generate a stable 38kHz signal using the Nordic?
I have been able to generate the required frequency however I am observing...
Not a question but thought worth mentioning.
developer.nordicsemi.com/.../
Good News
PWM library changes seems to have made it into the release.
Bad news:
Looks...
Hello,
I am working on an nRF51822 custom board application which is reading data from external sensor through TWI. It is based on the MPU6050 driver available in the SDK...
