I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi All,
I am new to the field and working on nRF51822. As mentioned in the question, which is the easiest way to Implement a simple LED blink (10Hz) for 5 seconds?. Is...
I have successfully tested the SPI master loopback example on pca10001 eval board. I have a few questions regarding a real-world scenario when there is a slave SPI present...
I'm trying to follow the instructions for "nRF51822 Beacon Firmware Documentation" for over the air firmware upgrade of the smart beacon, but I can't find the soft device...
Could this be my problem?
devzone.nordicsemi.com/.../s110-7-0-0-can-i-write-my-own-mbr
an application now starts at 0x15000 which is to make room for an extra 4Kbytes...
Hi,
I am new to BLE Development. Currently I am using NORDIC Development board (SDK Ver 5.2 &Soft device S110). I want to write a small program to establish the connection...
I'm trying to get a handle on the various ways I can implement console output on this system.
I have in the past used the retarget.c/.h code from this forum that uses simple_uart...
Hi
I use the random number generator of LE1,I have made a demo code and the code can generate a random number.As the project in attachment.
I want to get a random time...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
