I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
Hi all,
When I receive data from the phone app, I do it via this service handler (and it works):
err_code = ble_services_init(&my_device_service, ble_receive_handler...
error:-559038737 ...line:1128 file_name:src\ll_lm.s0.c
And I can't find this file, so can somebody help?
Why this happen? How can I do to avoid this？ It will cause reboot...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi
I would like to use the arm based energy micro MCU to update 51422 via UART
I've understood how the firmware update example with hci, but I need a set of hci api to...
Hello,
I in the nRF8002 data sheet it mentions a Programming tool for the nRF8002. Can you please send me the partnumber of this tool? Also, if a programming house wishes...
"Install the Master Control Panel and the nRF51822 Development Dongle (PCA10000)
Download and install the Master Control Panel from our website. Make sure to select...
Hi,
Been using nRF51822 before but on this new design I have an external MCU running the main duties.
I've been reading up a bit on both but would like to get some thoughts...
