I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I´m testing the nPM1300 in a custom circuit with Zephyr on an nRF52 / nRF53 attached to it. It looks like the IC isn´t charging a battery. For testing I use the nPM1300-EK...
Hello,
Can I use in production nrf52840-DK as programmer to program E73-2G4M08S1C module on custom PCB?
What should I do to make the program code unreadable?
Hello, I need further assistance with the issue in the mentioned ticket ID, as it was closed by mistake. Could someone please reopen it so I can continue the discussion? ...
nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. Using Tag 2 type driver library, nfc_t2t Occasionally, when NFC coil is tapped, we observe one of the...
Hello,
Our product uses nrf52 and a quectel bg95 modem connected over the uart
We are evaluating the nrf connect sdk, we seek to have a working modem abstraction to send...
We are designing a board with nRF5340 and need an external flash of preferably 512Mb (128MB) or more and 1.8V supply. For speed reasons it is best to use the QSPI protocol...
Hello team,
In our bin file, we are seeing " ZigBeeAlliance09" as String and how to avoid this string in the bin file? I am using SEGGER SES ID tool to generate bin file...
Hi,
I have a concrete example, where I have no clue, as to why a given configuration is not working. In general, I wonder, how one is supposed to debug / investigate such...
Hi All,
I am trying to migrate my toolchain/sdk v2.4.1 project to toolchain/sdk v2.5.0. And I am having these weird issues related to mbedtls. The same project without any...
Hello,
We tried using pcd_network_core_app_version() to read the network core version (presumably set by CONFIG_FW_INFO_FIRMWARE_VERSION in our hci_ipc.conf) from the app...
Hello If CONFIG_FOTA_DOWNLOAD_NATIVE_TLS is defined in the function fota_download_object_init() the variable dlc.set_native_tls is set to 1 and then in the function download_client_init...
Hi,
I think, I found a missing configuration in the QSPI driver for the nrf53 in nrfx_qspi.c. I've stumbled off this, while I was trying to configure MCUboot for the external...
We are working on a Zigbee-based network coordinator using the nRF52840. Our end device is connected to the coordinator, but when the end device leaves the network, it sometimes...
