My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
Hi there!
We are currently evaluating a low-power BLE system for a safety-critical wearable application that must transmit immediate alerts to a nearby receiver or mobile...
I followed the instructions at https://nordicsemiconductor.github.io/pc-nrfconnect-docs/create_new_app to create a new pc-nrfconnect-boilerplate app locally.
However, npm...
We have a common codebase with both softdevice (nRF51/52 code) and now zephyr (nRF54 code). To make our code compatible I have the following replacement to sd_temp_get. This...
Hello Nordic team,
We're experiencing a GNSS issue with our nRF9160-DK (PCA10090 1.1.3 2024.44) and would appreciate any guidance you can provide. About 4 days ago, we were...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
ncs v2.6.1
If I use bt_conn_le_create() and do not use the default (0) value for create_param->timeout, the actual connection creation timeout does not match the description...
I'm trying to program a custom board with a Raytac nRF52832 module using the nRF52 DK's onboard J-Link via the P20 debug out port. The J-Link only detects the onboard nRF52832...
Hi,
I've been working through the Nordic Bluetooth ESL Tutorial and have the sample code up and running (using a nRF52833 DK as the tag and a nRF5340 DK as the access point...
We have custom hadware which we can successfully added the bootloader. We can generate .bin files & bootload them via BLE using the Nordic devicemanger app on our smart phone...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
