Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
BLE Hello,
In my project i want to send the data from the nrf app to nrf52832 device and i don't know how to interface it with RPI compute module once the data received...
Hello, I have a question.
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral.
I have a question about the output time of the advertisements. The...
Hi,
I am develloping product witch ICM20948 and need to use magnetometer. I tried to move some existing and working code for arduino. I was able to get data from magnetometer...
Hi,
Our customer is optimize the size of flash used of nRF5340.
They are curious whether the definition in autoconfig.h are all used in the image? or some of them are...
I am testing nRF5_SDK_17.1 examples/dfu/secure_bootloader/pca10040_uart_debug
After I run on SES. I got this memory map. It overlaps softdevice area.
With armgcc ...
How do I use printf to output my own messages, and read incoming data, from a UART port that is separate from Zephyr's debugging outputs? This UART line will be connected...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Hi.
I'm trying to add a SPM partition to my project. Like another project i did in the past, i followed this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
We would like to know there is any direct test mode for TX power of NRF21540DK.
We only found the method of nRF52833 direct test(TX). But we can find how to do with NRF21540DK...
Hi,
I wonder how to use the internal capacitor of the nrf5340.
The nRF5340-DK operates at 32M=8pf 32.768k=9pf without any special settings.
If i use 10pf products for...
Hi,
I'm porting firmware between nRF52 and nRF53 platforms. What is the equivalent of NRF_UICR-> CUSTOMER on nRF53 to keep data like serial number etc.
Thanks
Sebas...
We are developing a custom device based on the nRF9160 SiP Revision 2 with multiple connections over LTE-M and we are experiencing problems with keeping our only TCP connection...
Hello, I'm using nrf mesh serial example in nrf5sdkformeshv500src, in the serial node i subscripted to 0xC000 but i can't not received messages more than 32 node, my netwwork...
Hi All,
Sorry to ask this question, I just learned a little about cmake.
Now I wanted to add a few src files based on the light switch example in SES. Do I have to create...
