Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
For BLE pairing I am using Just Works as there is NO IO and NO Display.
Could you please confirm...
Currently, I am only powering the NRF5340 chip to test its performance. I have opened a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart...
Hi, I’m currently working on a setup with three nodes:
Node A : collects data
Node B : acts as a relay, forwarding data
Node C : processes the data and then...
Dear Nordic Team,
I hope this email finds you well.
I am currently working on integrating group functionality with a Matter device (Node ID: 114, Endpoint ID: 1) using...
I was using an SPI serial nor flash device with NCS 2.8.0. I tried to get the flash into deep power down mode, but it doesn't seem to work well with NCS 2.8.0. So I upgraded...
Similar to ticket # 349557, we plan to operate nRF9151 in SLM mode and use both LTE and GNSS features. There is some interest in having GNSS (NMEA) data sent out on a dedicated...
Hi Team,
We have started our BLE development using nRF54L15 using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going to start...
NFC certification and library.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/nfc/README.html tells me, NFC is supported by nrf52 and 53.
e.g. libnfct2t_nrf52...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
We as a company love the app (nRF Connect) and use it accross a lot of devices to recover stolen goods with BLE.
However, on all my Android devices (modern tablets and phones...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hello, I am testing the system off demo on the nRF54L15 DK using nRF Connect SDK v2.8.0 (Zephyr v3.7.99). I ran the sample exactly as provided in the SDK .
Observed log...
I am using the nRF7002DK with the nRF5340 SoC. By default the board runs at 1.8 V until I provide 3.3 V on VIOREF. Currently, I am using another board just to drive VIOREF...
Hello there,
we're using multiple pwm-channels of one module of the nRF54L15 for different purposes (multiple motors, h-bridge control; depending on the project).
When...
