Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hello Jared,
the previous ticket find under the following link is locked. So I decided to open a new one.
https://devzone.nordicsemi.com/f/nordic-q-a/80312/uart-break...
Hi Nordic,
A important customer employ nRF5340 in their product, they are chosing the 32M crystal osciallor now.
Form the SPEC of 5340, if we want to communicate with...
I posted this theme, but the post is locked before fixed. I don't know the reason so repost. I'm sorry about this case.
-------------------------
Question:
I consider...
Hi,
I have a custom board with nrf52840 chipset that controls a GSM modem over UART, and this setup works just fine (zephyr project).
Now, I'm trying to replicate this...
Hi everybody,
I get this error trying to set coded_phy advertising on nrf52840 dongle. This is the code that i try.
The error that i get is:
That means I/O error...
I flash v1.7.0 at_client and mfw-v1.3.0 into nrf9160-DK board, LTE works normally and the board can get the ip. ( https://files.slack.com/files-pri/T0SBEQ7AR-F02J4REC8RX/nordic...
I'm trying to implement communication protocol that involves clock and bidirectional I/O line. Clock signal is coming from an external device and expected to be in 1-5MHz...
Hi,
Could you please help to fill which nRF9160 SIP revision fit for SDK?
nRF9160 modem firmware version
nRF Connect SDK
nRF9160-DK, SIP revision (BA, B0,...
Hello,
I have a question about the best way of implementation.
The data will consists out of a struct with multiple pressure and temperature measurements coming from another...
Hi everyone,
I have this question to ask. So I am trying do make an end device that run on low power. I can see that there is an example about the sleepy end device in the...
Hello everybody,
I wonder if somebody could give me an example of an easy way to use saadc without using any adc_event_handler for sdk 15.
I'm trying to do it myself from...
Hi,
I connected an external MCU and going to run AT commands sequence by using serial port (UART2).
Can someone provide the sequence of AT commands to get fixed A-GPS...
Looking for advice on reading data from the BL654 UART RX pin which is getting a text data stream from an STM32 micro.
I tried the "peripheral_uart" sample app in Segger...
