Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
When using the local timer of the SAADC it should be started with TASK_START according to https://infocenter.nordicsemi.com/topic/ps_nrf52840/saadc.html?cp=4_0_0_5_22_4#concept_continuous...
Hi there,
I'm interested in using LittleVGL (lvgl.io) for my project. There is a LittleVGL example using nRF52840 in Zephyr project, but no in the nRF Connect SDK. Are...
I have successfully implemented the meander PCB antenna outlined in this app note, however, I am looking for and cannot find information on a shrunken version of this antenna...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
As noted in recent past cases, we have an issue with the state of the nRESET pin that is causing unwanted resets when connected/disconnected from external hardware (programmer...
I used NRF52840 Base on NRF SDK15.3 and freertos.
I have two task call nrf_crypto_aes_crypt a t the same time occasionally return NRF_ERROR_CRYPTO_BUSY. And also I add mutex...
Hi
I am developing with nrf52832 development board and sdk17. I'm trying to communicate with redpine rs9116w through spi but get some problems.
I have an other nrf52840...
Hi,
I'm a beginner at this, I'm a software developer so I've never worked with hardware but now I need to and I don't seem to be able to make it work.
I would need help...
Hi,
I have nRF9160 Power Measurement DK board, (PCA63511 Rev 1.1.0). And
nRF52 dev boards (nRF52840) (PCA10056)
I measured my program as: with nRFConnect version 3.2...
