Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi
it's possible configure the FOTA bootloader (SMP service) whit only one partition, for large application.
I using the nRF52-DK and have only 512KB of flash, and my...
I have trouble getting NFC-pairing to work in nRF52840 running SoftDevice 7.2 based on SDK 7.0.2. The observed behaviour is that the NFC Field is detected but nothing more...
Hi,
I add a new service about DFU of my FW，so three was a problem when it go into "ble_nus_init()" will return NRF_ERROR_NO_MEM, I have read serveral tickets about the same...
i have used "BLE_GAP_PHY_AUTO" in scanner code
actually it should scan "phy coded" and "non phy coded" aid values .
but in my case getting i was getting both "phy coded...
I have a project to use NRF52810 to connect the App. When testing it, I found that when it was successfully connected to the NRF Connect tool, it would automatically disconnect...
Hi, Dev Zone.
thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
1st_question <- this is my first question links
main problem...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
My project has requirements for tow...
development tool : Segger Embedded Studio
SDK:nRF5_SDK_17.0.2_d674dde
it always takes long time to build project
build log:
Building ‘blinky_pca10056’ from solution...
Hello all,
I am developing an application from the ble_cgms example on the nrf5_sdk 17 using the Softdevice S132.
I have implemented a gpiote interrupt whenever the state...
Hello,
I just received nRF9160DK(PCA10090, 0.8.3)
I followed nRF9160_DK_Getting_Started_Guide doc.
But, I hare some issue to activate iBasis Sim card.
It keeps...
Hello, I am using the latest version of pc-ble-driver combined with a pca10040 and I am attempting to write large data packets (200 bytes) to a peripheral. I compiled the...
Hi,
I have tested FOTA code in nRF52840 DK and it works perfect but i have custom board build with nrf52840 when i implement the code it doesn't get start
custom board...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
