Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hello everyone.
I have a nRF52840 DK that I am working with.
1.) When I plug into the USB port J2 (MCU interface) I am able to connect to the board program/debug using...
I wrote some code that has multiple custom services where my device acts as GATT Server.
I register the handler for every service (3 in total) with NRF_SDH_BLE_OBSERVER...
Hi,
I am debgging QSPI( type name: IS25LQ040B) in nRF52833, I met " NRFX_ERROR_TIMEOUT ", Could you give me some advice, please?
// Set QSPI pins to pins related to...
Using this \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky and nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c
As described in \examples\ble_central...
Dear community,
I'm facing a problem during bluetooth scanning. I'm using the example named in the subject. This allows me to use the UART as debug printout.
I slightly...
Hi, I'm trying to upgrade nRF Connect SDK from 1.3.0-rc1 to 1.3.0 because I need one of the bugfixes to keep developing. I'm on macOS catalina and I've used the Toolchain...
Hi,
I am looking at and testing the ble_app_hrs_c_pca10040_s132 example.
When the whitelist ist set up with the "whitelist request" we execute the following two lines...
Hi,
I am developing an application that requires communication between two nrf52840-based devices. There is a scenario in my application where the devices needs to exchange...
Hi,
[179] RTC: COMPARE event is generated twice from a single RTC compare match
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
