Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi Team,
Nrf52840 DK acting as central and we trying to connect our peripheral device, we observed below logs with total duration of around 300ms.
Is there any way limit...
Hi forum,
I am working on nrf52832 using sdk15.0.0. using project ble_app_beacon.
In this project I am setting tx_power 0dbm,4dbm,-4dbm and -8dbm.while setting this tx_power...
Hi, Nordic
nRF52 as GZP Device, nRF24 as GZP Host
I know if nRF52 is range of nRF24, the pair will be worked.
I want to know what is the distance.
And if I use unencrypt...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
Hi
I want to receive data through UART RX interrupt.
--> A n interruption occurs to notify me w hen one character(byte) is received, and i store it to my memory buffer...
Hi everyone!
We're working with the processor nRF51422 with S210 softdevice and we've found an issue about the QDEC sample frequency. In fact, the minimum sample period by...
i have nRF52840 Dongle (PCA10059) and when i connected the dongle and opened nrf connect SDK application and tried to run BLE, then i am getting the following error. Kindly...
I am following the step to install my nRF52DK, but when I check it with "python3 nrf_sniffer_ble.py --extcap-interfaces", it has some error:
Could anyone help?
Hey!
I will post the whole code if necessary but for instance as I thought it would be a little glitch in my code, I tried to explain the basics of my problem for now: ...
ASSET TRACKER V2 Modem problems:
I have set up asset tracker V2 for nRF9160 and it sends the messages (GPS, Temp, Hum, etc) and the corresponding timestamps, which I can...
