Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
I am running the example code:C:\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc
I am using PCA10040 dev board.
When...
I am attempting to use a one shot application timer. This works fine when I use the event handler to perform a specific task toggle an LED for example. But I would really...
Good afternoon,
We have developed a new equipment based on the nrf52840. We use sofldevice 's140_nrf52_6.1.0_softdevice' and we use bonding with static pin.
We have setup...
Hi,
Is it possible to generate Complimentary PWM in nrF840? Do i need to use the PWM in Individual mode?
My application is a synchronous buck converter
thanks,
th...
Hi all,
I have RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha image for BorderRouter and need to work with Command lines in Command line Interface(CLI) and with diag commands...
Hello,
I have recently received nrf5340 development kit.
To get my very first stamps of programming given precompiled image peripheral heart rate, I
1. Connected board...
Hello,
I want to evaluate the ble_app_buttonless_dfu example (C:\nRF5SDK160098a08e\examples\ble_peripheral\ble_app_buttonless_dfu). I am using the nRF5 SDK 16.0.0, IAR EWARM...
I have an nRF52840 - install the BLE Sniffer Software on it - play a littel Bit - happy :-)
(dont help me to scan the communication between 2 devices - but thats a other...
Hi,
I need to test the data rate capacity between a nrf52840 and a smartphone. Smartphone being the central device and nrf52840 being the peripheral device. I have an...
Hi,
What hardware configuration settings that I need to change when moving from Development Kit(NRF52832) to BL651(NRF52810)?
I can run all examples from "nRF5_SDK_17...
Based on the datasheet table 166 can the drive strength for SCL/SDA pin is mentioned to be selected as S0D1 can it be changed to H0D1 drive strength? Since based on the IBIS...
Hi! What is the proper use of sd_ble_gap_adv_stop in SDK 15? I'm using nrf52832 in my application but can't seen to find a corret way to stop advertising.
Looking on ble_gap...
Hi all,
I'm using Raspberry Pi with Nordic dongle and flashed the Nordic Alpha 4.1.0.1 image to make it as BorderRouter in NCP design.
I have EFR32device and have flashed...
Hi
I'm using nrf52832 custom board with 14.2.0 SDK version and trying to communicate TWI interface with LTC2631 DAC converter. I tested my sensor hardware with Arduino and...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
