I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi, I want to run unit tests on an actual device (nRF52dk) - is it possible? When I'm trying to run `west build -b nrf52840dk_nrf52840` on `ncs/nrf/tests/unity/example_test...
I ask for your understanding of my short English. I am a student studying in Korea.
i using sdk 15.2 and nrf52840 dongle
When using the example of usbd_ble_uart of peripheral...
Hi,
im use the example of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and i change the code of static void hids_init(void) like this:
and...
Hi
i have installed segger emstudio and almost all dependencies but still can't able to build a project. my main target is to work with nrf9160 dk but without an hardware...
Hello!
I'm working on a project with the new nRF5340 & Zephyr and I'm trying to get two SPI peripherals on the same bus sampling data correctly. It's a simple program thus...
Hello,May I ask you a question?
Hardware model: NRF51822 SDK version: SDKv9.0.0 SoftDevice:s110.
I used the interface in the pstorage.c file to realize the storage of...
Hi there,
I'm just trying to start to code my project. I want to stream 48k 16 bit audio from one nrf52840 dongle to the other one. I only need one way transfer.
I have...
Hi,
I want to use dtm project to test RF PHY performance about NRF5340. But after downloading dtm project and empty app project, NRF5340 can work normally from output RTT...
Hello I use nrf52832 and sdk v17.0.
I'm testing the firmware using custom pcb. Sometimes it stops altogether if there is an error in the firmware during the test.
The...
Hi. I'm testing our new product that can be extend ranges using FEM.
For best performance, I'm matching impedance between antenna and FEM.
But my major is not wireless...
Hello, I have a problem with my own designed board, It has nRF52832 and some other sensors which communicate over SPI, also I have a SD card on the same bus that works fine...
Hello,
In my code I am reading from a sensor and want to check if the float value returned is out of range. In order to do so I would like to be able to calculate the absolute...
i have just blinked the LED and trying to pwm
i have written a simple led blinking program like this one below
#include <stdbool.h> #include <stdint.h> #include "nrf_delay...
I'm trying to diagnose frequent (80%) DFU failures that I'm seeing with our Android application using Buttonless mode.
Our target can be 100% reliably updated with our app...
