Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
I am a newbie with nordic, where I have recently purchased the nrf52810 device. I need some guidelines to get started. My intention is to read data via TWI from an MPU6050...
Hi,
In past we have observed BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION as a disconnection reason when the application layer tries to disconnect because of a timeout. But...
Hello, we are developing a project solution where we want to pass data between multiple sensor devices using BLE advertising data. For now, we have a test setup with two nrf52832dk...
Hi,
I would like to catch in main.c the nobody connect after advertising event via ADV_SET_TERMINATED.
I can see with breakpoint program jump into ble_advertising_on_ble_evt...
Hello
I am making a button double-click function in sdk v17. I've tried 'app_button' and 'app_timer'. Created a timer that is called every 0.1 seconds and terminates when...
Hi there,
To put a little bit of context, I've designed a wearable that is now going towards pre-production (only some minors fix left to do). In the last iteration, we...
Hi，all:
I use 9160DK to test PSM mode as follow steps with at_client example：
1、set ”AT+CFUN=0“ to power off mode;
2、set "AT+CPSMS=1,"","","10101010","00100001"" to...
Hello,
We're making RuuviTag sensor beacons which log environmental data to flash. Logged data is later read by a mobile phone application over Nordic UART Service.
The...
Hello
I am programming using the nrf52832 module 'MDBT42Q-512KV2' in SDK v17.0.
This works well without any problems in the example ble_app_blink. However, the BLE is...
Hello
I am contacting you to have a little more information concerning the messages which are sent in the examples thread_simple_coap_client and thread_simple_coap_server...
We have performed the DTM mode setup on the ATEX HW variant of nRF52832 chipset using nRF go studio application where the app is throwing an error as attached in the screenshot...
This is more related to the Segger Embedded Studio than Nordic parts or SDK, but I'd like to hear what kind of experience other Nordic users are having with the Segger IDE...
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
