I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
I am trying to run the SDK15.3.0 gfx example code - only changing line 82 to:
And also I have changed the sdk_config to the display's width and height. I have wired it...
hi
I want to update RTC time in my device nrf52840 through nrf connect app. How can i do this? Is there any related example which may help me in doing this?
Hi,
I'm attempting to use OpenOCD to perform the equivalent to "nrfjprog --recover", since we've recently started using that feature.
I read through this case, but it...
Version 4.20a (Win x64) of Segger's Embedded Studio has problems with it's C syntax highlighting -- specifically conditional compiled sections of code. Code that is not being...
Hi,
We are using nrf52840 to develop a cryptocurrency hardware wallet. We want that user can verify that the device is authenticate. In order to authenticate, the desktop...
Hi,
I'm using Kail and I have a project with original target device nrf52832xxAA, I need to change it to nrf52832xxAB (the device onboard is nRf52832QFAB).
When I...
Hello,
I have to send SMS from NORDIC nrf9160dk which is using iBASIS sim card to my mobile phone. For this I tried two programs (at_client and simple_at). But nothing works...
Hello,
I am trying to run https://github.com/sigurdnev/fw-nrfconnect-nrf/tree/master/samples/nrf9160/i2c_scanner exampl. It is not compiling with the zephyr right now...
Hi,
for a new project we use the NRF52480, I can get it into low power mode with a total use of 20µA ( with all the other hardware on the board ). But when I initialize...
As far as I can tell, the packet sent by nRF24L01+ PTX only contains a destination address. There if no information that identifies the transmitter (i.e. PTX).
So, when...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
