I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
Hello,
Can I send data from nrf52832 to nrf24l01p? If yes, please suggest me the simple code for it. I tried to send data but it failed. Here is my piece of code :
Transmitter...
I have the nRF52 DK board and I cannot see the device in the list in the nRF Connect app (iOS). Here's what I have tried:
Connected the nRF52 DK to my computer with micro...
Hi all,
I have tried to flash the blinky programm to the BMD 300 AR evaluation board by nRF command line tools but I can't flash the .hex file to my evaluation board. The...
I followed this tutorial :Bluetooth low energy Characteristics, a beginner's tutorial
i am beginner to study BLE.
I wanna the answer Challenge 1: Why are you not allowed...
Hello,
Our setup:
IDE : Segger Embedded Studio for ARM V4.12, nRFgo studio
SDK : nRF5_SDK_15.2.0_9412b96 + SDK for Mesh3.1.0,
Softdevice : 6.1.1
Computer Platform...
Hi, I'm using SDK12.1 example ble_app_ancs_c.
Is it possible keep advertising (non-connectable is ok) when ancs connecting?
And how to do it?
I tried call advertising_start...
Hi,
I have been having issues with the compile hex files I get when following the steps to build the pc-ble-driver (). While I am able to build the hex files when I place...
I got Orange sim connected to LTE-M network on nrf9160 DK, verified it on LTE link monitor. But when i tried adding a LTE device on nrf connect cloud, i am not able to register...
Hi,
I tried to build the lte_ble_gateway sample in SES, however it gives the error below regarding the UART.
Any suggestions how to resolve this issue?
Hi,
As mentioned in the subject, I am confused with the SPIS example from nRF52 SDK 15.3.0. I wonder where NRFX_SPIS and _INST_IDX are defined in the header file?
SPIS...
Hello,
I am testing the Light Switch example and I observed a problem:
- I noticed that it was possible to reset the "server nodes" by pressing their "button 4" to leave...
I am having an issue migrating some code over from Keil to an example in SES studio.
The code in Keil is simply listening for a radio packet, when it receives it, it transmits...
