Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hi,
I want to read a IC register over SPI.
This is msp430 code,it works. Just
CS low
write address
write 0x00
CS high
I use SPIM, this is initialization
...
Using an nRF52832 with SDK15.2 can I have multiple SPI devices;
one with DMA and one without DMA?
And can one instance be of legacy type (nrf_drv_spi) and the other be...
We use Rigado BMD-300 module with nRF52832 and softdevice S132 v6.1.0 as peripheral. Trying to create test plan for Bluetooth qualification , but with new TCLR there are inconsistencies...
Hi,
Recently, I faced very weird problem which stops working MCU when MCU enters low-power mode.
Not all PCBA I made have the same problem but quite many PCBA shows the...
hello, this is my first time to start the PPK, I have a 52840 DK (BMD-340-EVAL) and PPK, when I use nRF connect to connect the PPK(PPK is over the 52840 DK) , it shows Failed...
Hi Nordic Community
I'm busy developing a board around the nRF9160. Do you have a KiCad library/component for the SOC, do I need to make one myself, and if you do have one...
I'm trying to use the SPIM driver on nRF52832. The setup is:
Chip: nRF52832
SDK: 15
Softdevice: s132 v6
Toolchain: GCC
For some reason the call to nrfx_spim_xfer...
Hello,
I'm trying to configure the max -min of interval params and supervision timeout to obtain timeout of android = 1s.
i configure all parameters to run function...
Hi,
I am using the nrf-52840 DK.
I modified the pwm_library to output 125khz frequency.
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(125000L, NRF_GPIO_PIN_MAP...
Hi ,
The nrf connect for desktop programming works good on my desktop before.
The tool shows error message "cannot find module 'usb' " today.
I ever try re-install the...
I am working on integrated peripheral and central device used for indoor positioning. The device has two modes, at boot it is a peripheral for some duration of time then it...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
