Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi, may I looked bad , but I can not find NTF52 documentation, datasheet, evaluation board schematic, pinout, price... nothing , except the file nrf52.h in which I found some...
The following SDK files have incorrect comments:
markrages@qountdown:~$ grep 'units of 0.625' -r /opt/nrf51sdk-11.0.0 | grep 300 | grep to\ 25\ ms
/opt/nrf51sdk-11.0.0...
I configured nrf to go to sleep after 5 minutes of inactivity and then wake up by external signal (by accelerometer interrupt if any movement detected). what struck me is...
Hi again,
I'm here with another HID problem. When I flash my chip with standard HID mouse example, OS discovers it with it's declared in code name, connects succesfully...
I have designed an custom application board based on nRF51822 SoC,
Now i wanted to do testing on RF front.
I found one Test guideline(RF_Performance_Test_Guidelines_v1_0...
Hello Everyone,
I am able to do this functionality by using NRF5DK
Using Android APP (MCP master control panel) am able to make beep sound in the NRF51DK by using...
Im working with a nRF51422 EK. So, there is an android application with 2 buttons. Each of them can Set a LED. It will be set as long as the button is pressed on the application...
SDK:10.0.0
Here is the error when I compile
..............\components\softdevice\common\softdevice_handler\softdevice_handler.h(40): error: #5: cannot open source input...
Hello,
I have a project which is currently using S110 SoftDevice v7.1.0 with nRF51 SDK v6.1.0. The hardware is nRF51822 xxAA revision 2. It will probably be upgraded eventually...
Hi,
I intend to use ANT protocol for an application of soccer players trackers.
Each soccer player would wear One master and remote sensors communicating with ANT.
But...
Is there a way to know if we are in critical region?
ie: between sd_nvic_critical_region_enter(&foo) and sd_nvic_critical_region_exit(0) without explicitly using a global...
Hello,
I'm using nRF8001 with Arduino for our project. I use BLEeripheral. h and I need to know if it's possible
with the visibility of NRF
when invisible can nrf...
Hi,
everyone,
I am new with the uvision IDE.
Can anyone tell me how should I supply source and header file to project so that my header files can be access without relative...
I'm curious. I believe I can set it up in the keil "options->target" tab.
I get it that as long as I don't cause the softdevice and my program to "overlap", it is fine...
