Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
Hello,
I'm working on a project that involves using an NRF52832. Basically, I want to collect data, send it over bluetooth, and then have the device enter system_off mode...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I'm trying to get a basic CI/CD pipeline working in Azure DevOps, using Azure hosted agents, and I'm running into a problem where West is silently failing to clone the project...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hello everyone.
WE're trying to make a https connection with google.com and execute a GET request.
Wifi connection is working; DHCP seems to be working (my personal assumption...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
Hello, I need help understanding how MCUBOOT produces signed_by_b0_app.hex file from app.hex on the network core of nrf5340. My goal is to have a DFU updatable hex file (net_core_app_moved_test_update...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
I have a couple questions regarding the Bluetooth Mesh provisioner role and TF-M builds.
I am using an NRF54L15 and currently swapped to v3.01. Previously on versions <3...
Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140
I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
