Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Good morning,
I have already implemented my application based on nRF51822 and SD110 v8.
In what regards bonding, I use a static passkey and it works fine.
The product has...
I will use the functions in app_timer to set a timer to fire every 3 seconds. I want this to occur "forever" (e.g.until a restart of the nRF51).
To avoid a timer overflow...
Hi,
I am using the nRF51-DK board as a central running with ble_app_multilink_central_s130_pca10028 sample application. I am using SDK version 9.0 with Keil 5.14 version...
Hi all! I am using the nRF51 DK and I am trying to use the elements demo APPs that Nordic provide - the Beacon app. after the downloading of the app and watching it working...
Hi
In my application, I use some of the IO pins for a multi-purpose sensor interface, that I would like to be able to configure when the application is running. The interface...
Hi,
Can anyone help me where can find the example ble_hr ? I have changed the main file and it is saved and now I want the original example that was in C:\Keil_v5\ARM\Device...
I have IAR Embedded Workbench 7.40 installed with nRF5x_MDK_8_0_3_IAR.msi. However when i select nRF52832_xxAA i get the below message:
WTD: Unavailable option selection...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
