Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Now,I have a project writed by nRFSDK17.And I want to rewrite it by NCS.
I hope to get a module like peer_manager to manage paring and bonding,and I can distinguish connecting...
The status of Docker support is not clear to me. Does Nordic provide a docker images than can be used on Apple Silicon and Integrated with Visual Code Studio. I see a lot...
Hello developers, I am using nRF5340dk as my nodes and my gateway also. (3 boards).
Requirement:
i want to send my data from the board(1) to gateway with the help of mesh...
Hello,
I'm trying to configure the internal temperature sensor but have no idea ...
My board selection is raytac_mdbt53_db_40_nrf5340_cpuapp and, on nRF Kconfig GUI, I...
Hello, I am working on developing a special "serial recovery" mode dfu function of nrf52833 with ncs SDK V2.3.0. Now I encount a problem when adding the following code in...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v2.4.2, after successfully build and flash the program to nRF5340DK I got error "Device...
Hi all,
I am developing an application for a custom board using the nRF52840. I need to use the reset pin (P0.18) as a regular GPIO, configured as an input with an associated...
nRF5_SDK_15.0.0_a53641a s140 nRF52840
Documentation says that both ble_adv_fast_timeout and the ble_adv_slow_timeout are in units of 10ms, and that appears to be true of...
I have read some of the Asset Tracker documentation and noticed there is a nice implementation for operating LEDs in the UI module. This seems straightforward for GPIO control...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
hit there,
i am trying to work with the NRF5 SDK ARMGCC, in the IDE options a ARMGCC folder exists with an .ld file and makefile. i run the make and get the following error...
Hi,
I'm aiming to develop a custom two-wire serial interface (TX, RX). To achieve this, I'm planning to implement output capture for TX and use GPIO interrupts for RX. For...
NCS v2.7.0 and sysbuild system.
I'm looking for some clarification about Secure Boot and implementing a custom signing command.
What is the difference between secure boot...
software: ncs 2.5.0, zephyr/samples/subsys/fs/fs_sample
hardware: nRF52840 (not DK, designed by customer) and nRF52832 (not DK, designed by customer)
Step1: build within...
Hello everyone
I'm trying to build an app using Segger Embedded Studio and a nRF52832. I'm currently struggling to include the fds module since i get the following errors...
