Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
What's minimum hold time for a pin reset on nRF54L10? https://docs-be.nordicsemi.com/bundle/ps_nrf54L15/page/pdf/nRF54L15_nRF54L10_nRF54L05_Datasheet_v1.0.pdf doesn't state...
Hello, I am developing an application that uses Bluetooth Channel Sounding, and for that reason I need to have two devkits connected to my computer at the same time, but the...
Hi there,
I was designing an add-on development board to go onto the development kit to test a 1.8V application. I need VDD:nRF on the 54LM20 to be set as the same as VDD...
I connected the new nPM2100 EK to Linux PC and opened the nPM Power UP application. In the app I'm able to select the EK. The nPM Power UP tells me that " Programming required...
I have an NPM1300 demo board. After testing, the default voltage of VOUT1 is 1.74 V. If I use this voltage to power the VDD of nRF54L15, will it affect the power-on reset...
Hi Nordic
We plan to use 54l15+7002e, how much storage will spend for nRF7002 up layer stack and application(e.g typical Wi-Fi STA with TCP client connections)?
What I've tried:
Testing Summary: SD Card on Port 2
Setup : Wired an SDHC card (Transcend 8GB) to the Connector P2 (middle header) on an nRF54L15 DK v1.0.0...
To ensure fast and efficient ticket handling: Please describe the problem as accurate and to-the-point as possible. Include all the details needed to reproduce your situation...
Hi Nordic Support Team,
I am working on a Matter application using the nRF54L15 , and I have a few questions regarding the external flash configuration.
I noticed that...
nRF Connect SDK v3.2.1, nRF9160dk
Hi,
I'm working on an application which connects to a MQTT broker over cellular network, and have MCUMGR enabled for firmware updates...
Hi，
There are 8K functions in nrf_desktop, but this example is too complicated. My own example is relatively simple. I want to integrate 8K functions. At present, overlay...
