Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
I try to set custom compiler flags for the whole project including Zephyr via prj.conf / CONFIG_COMPILER_OPT to compute worst case stack usage as follows: CONFIG_COMPILER_OPT...
Hi all,
I am having difficulties reading microphone data using built-in microphone at Xiao Seeed nRF52840 Sense. I have configured the overlay file as suggested here . Then...
Hello,
I am following the cellular IoT fundamental course with nRF9151-DK.
I didn't have any issue until Lesson 7, but I found that the screen shot of the lesson is...
Hi devzone,
I am starting to write some tests for my application, and I have a couple questions/remarks about the provided Docker image. Link to documentation .
1/ The...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
Hello Nordic team,
We are using the GRTC on the nRF54L15 , and we are observing the following behavior:
When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
Hi, I am using nrf9151 as a modem running SLM. When SLM comes up, it throws this error. This is a new board run and 50% of the boards show this issue.
I appreciate there...
I am looking for a pairing between Windows laptop or Android mobile on the transmitter side and hearing aid which has bluetooth streaming features as a receiver..
I am looking...
Hi there,
Is it possible to have the DECT NR+ modem trigger events via DPPI? For instance, I'd like to capture a Timer value *exactly* when nrf_modem_dect_phy_time_get...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
