Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I currently use nrfConnect on android to download firmware to nrf52832s. I am just getting started with nRFUtil and the dongle.
If I understand correctly, I should be able...
I have a nRF52 DK from DigiKey that I've been evaluating and I ran into an issue: I had a custom app that was talking through Bluetooth and sharing some custom characteristics...
Hi, I'm using NXP LM75B temprature sensor based on nRF SDK's example code.
I would like to save power on this sensor.
I have prepared the code as follows:
Following...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
I'm developing for nRF52832, SDK 17.0.2 and softdevice S312 7.0.1.
After I upgraded from Segger Embedded Studio 6.22a to 6.30 I found that turning on any compiler optimisation...
HI DevTeam,
I'm using the nRF52840 as co-processor due to the semiconductor shortage and I don't need to use the RF section. What should be done with the antenna pin in...
This is the implemenatation spec for GATT server database (reader) firmware i am working on.
I have implemented advertisement packet using nRF Connect SDK latest.
Not...
Hello,
I am customizing the BLE DFU bootloader for nrf52820. Integrated an LCD to it.
Now I need to display the percentage of firmware download on the LCD. It will take...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
STEVAL-STMDLTE WITH NRF52840 using UART
We are trying to integrate the STEVAL-STMODLTE Link chip into the NRF52840 for rapid prototyping.
Trying to interface nrf52840...
We notice that upgrading from nRF Connect SDK 1.8.0 to 1.9.0 was generating issues in our application. Now we notice that nRF Connect SDK 2.0.0 is dropping the Segger supprt...
