Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello!
The NRF52832 based Raytec Module, the Garmin NRF52 module and the Nordic Dev kits all handle the Mesh firmware I have developed without change or modification and...
Hello,
I'm trying out the Matter: Light bulb example using an nrf52840 device. So far, I have managed to build the software, flash the device, provision it into the network...
Hello Nordic Semi team,
I am porting the Modem Library to run on a different OS.
The documentation provide is great, but I have a two minor questions.
1. The documentation...
My setup:
Mac OS 11.5.2
Vs Code 1.60.2
nRF Connect SDK 1.7.0
nRF52840DK
Using the tutorial videos provided I went through the process of creating the basic blinky...
1.How exchange datas between applacation core and net core, can provide demo code？
2.How does the APP core call the API in the NET core, and how does the NET core call the...
I'm having problems using the UARTE in the nRF52840 via Zephyr. I'm watching the TX pin using a logic analyzer and seeing correct data when running at 9600 baud. But if I...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
The example provided for ble_peripheral...
Using SDK 17
There must be a way to show all commands in RTT without needing the tab to work right?
Ive been digging through the code but don't see where the magic happens...
Hi, when i'm debugging my circuit, the logical of a if or while don't work. In the image, the timeout_rtc is higher than 100, but the value of a don't change to 1. What's...
I used the P1.13 pin of NRF52833 as the output pin, and used it in the manner of the blinky sample program, but it crashed and prompted the following error message:
***...
Hello, I have a custom HOST board. There are use NRF52840 BLE chip.
I'm run Bluez 5.61 on the HOST board and by meshctl> I am able to run as a controller. But if I want...
how to set BLE_GAP_ADDR_TYPE_ANONYMOUS
i have follwoed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners...
Hi,
There are tons of documentation on how to make a mouse, keyboard or remote control work as a HOGP device, and I have successfully implemented both mouse and remote control...
Hi,
Using NRF Connect 1.6.1 on NRF5340 I have modified hci_rpmsg project to add another endpoint for bidirectional calling between app core and net core. I have used the...
Is there a reason that AT_CLIENT example always works for LTE but SERIAL_LTE_MODEM only works the first time, and then trying again it never connects to the LTE ? Typing AT...
