Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
I have merged these two codes from SDK:
\nRF5_SDK_17.0.2_d674dde\examples\peripheral\timer
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon
I want...
Hi,
I have nRF52 dev boards (nRF52840) (PCA10056), I am using SoftDevice nRF5_SDK_17.0.2_d674dde.
I am not sure SoftDevice SDK 17.0.2 supports BLE 5.0 specification: ...
Hi I am using Ncs version 1.6.0 and nrf52840dk ..BT_HCI_LE_SCAN_FILTER_DUP_ENABLE this duplicate filter enable is not working in NCS.is there any workaround for that?
I have a question regarding the power sequence mentioned in the nRF52833-Dk guide:
or the power sources section the guide explains it as:
I drew the...
Hi,
I know that this question was asked before, but I can't find a complete/recent answer.
We are trying to use nrf52 DK board to perform bluetooth localization. In...
I have a few questions about the bootloader of the nRF52.
I used "nrfjprog --eraseall" to erase the chip, afterwards I turned the power off and on again while holding down...
Dear Community,
I implemented the beacon-example with S112 and 1MBit mode and with S140 and coded-phy 125k sending one beacon per second continuously at +0dBm (sd_ble_gap_tx_power_set...
I have attached a sensor board to the nRF5340DK board I'm using zephyr 1.6.0 on macOS
I ran an I2C scan example using I2C1 peripheral and it works fine
found 5 I2C slave...
Hello, I have an issue. When I disconnect device I need to know it's mac address. Can you answer, how do i can get mac address of disconnected device or list of mac addresses...
Hi everyone,
I'm working with the BMD-350 Evaluation Board based on the nRF52832 BLE SoC and currently using a customized version of the central ble_app_uart example from...
We have an existing product that uses a module containing NRF52832-CIAA
Due to supply issues we are looking to respin our board to use a different module that contains NRF52832...
When I reset the device and in some time connect it to JLinkRTTViewer, it shows only 11-12 first messages after the reset. Which parameter I should change to increase number...
Hi, I tried to create standalone project based on SAADC example from nRF SDK. I copied all neccesary .h files etc., changed the include directiories. But then appeared some...
I want to try NRF52811 EYSNCNZWW with Jtrace but i am not getting how to implement this.
I have Cortex-m Reference board which uses STM32F407 micro controller, it has dedicated...
Hello, I found this blog post in google and I decide to try it. I have couple of NrF52810 currently that we struggle with the limited space and the solution described in the...
