Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hello, I have 2 PCBs for drone communication using nRF52820 and nRF21540 FEM module. I'm using the ESB protocol to communicate via radio. There are ready-made esb_prx and...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello everybody,
now, I am solving problem with switching off Wi-Fi interface on nrf7002-DK. I am runnig SoftAP example on my nrf7002-DK board. So my board behaves like...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
I'm developing my application with nrf52832 and nrf SDK v17.
I'm testing my program.
After running for some time, Jlink output the following.
When the "Logs dropped...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but it flash but can't run RF...
hi，all
Chip: nrf52840
SDK: NCS 2.9.0
We are currently developing an integrated factory testing function using mcuBoot's DFU. We want to make slot 0 the default for factory...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
Hello,
I am having nRF9160 with modem FW = 1.3.6 and nrf sdk version 2.7.0
I am using MBEDTLS library for generating self-signed & CSR certificates with EC-Key and RSA...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
