My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
Hi, does Nordic provide the "works with all hubs" Zigbee cluster?
I see this blogpost mentioning " Watch out for more information on future Zigbee 3.1 SDK All Hubs support...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Board: nRF52840
Hi, I'm a newbie in zigbee stack. I have been get started with the door lock example.
I want to make custom...
Just wanted to share how to interface a thermistor (103) with Nrf52840 and get the values over a BLE android app (Nordic toolbox). refer here,
github.com/.../Thermistor...
Just wanted to share the project for interfacing IR distance sensor with Nrf52840 and get the values over BLE app (Nordic toolbox)
github.com/.../distance-sensor-with-N...
