Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
I'm trying to make an application which displays signal transferred via bluetooth.
To reduce computing time on the tablet, I want to apply oversampling in nRF52840.
The...
Thanks in advanced. I achieve 4 uint8_t dynamic sensor datas, I want 52832 transmit them through BLE continuously. Based on examples\ble_peripheral\ble_app_gatts_c, I can...
Dear,
How to evaluate a channel if is clear in property in NRF528 serials? e.g. there are ED and CCA in 802.15.4 standard, how to implement CSMA in NRF52810?
Hi
I'm using nRF52832, SDK 16.
When I enabling timer application the power consumption is increased by ~450uA, far away from the product specification
What may cause...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
Hello,
I want to use BLE direction finding. In the product brief ( https://www.nordicsemi.com/-/media/Software-and-other-downloads/Product-Briefs/nRF52833-DK-PB-10.pdf?la...
Hi,
I need some help to interpret the LTE timers values that my network operator applies.
During network registration I requested RPTAU : 10 min and AT : 0 min, by issuing...
I want to connect the nordic ZigBee with Digi's XBee module.
I have configured the Digi XBee pro s2c module as coordinator and nordic as a router but they are not communicating...
Continuing the discussion that was documented here:
https://devzone.nordicsemi.com/f/nordic-q-a/64691/how-to-use-the-latest-version-of-californium
1) I modified the resources...
Dear Nordic Support Team,
I haven't seen any forum posts directly applicable to the issue I'm seeing so I hope you can point me in the right direction.
The basic Thread...
I wanted to try to test some of the nrfx_saadc v2 features in a project I'm developing. I downloaded and ran a couple of the examples from GitHub and they run fine on a nRF52...
Hi,
we are facing the following error. We bond our device (peripheral S140, SDK 15.3) with the following settings with iOS devices:
#define SEC_PARAM_BOND 1 // Perform...
Hi,
I am unable to build code. My Mac has just been updated to Catalina, not sure if that's caused the issue.
I am trying to build the standard "blinky" code but am getting...
