Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
I am converting the simple_on_off vendor model to send a message on mesh 3.1.
the server implemented the simple_on_off model successfully. But but my client runs into 0...
Hi currently I am using the nrf_mesh_sdk_3.1 latest release light_switch Example both client and server one after successful compilation and load examples in DK boards when...
Hello,
I have updated secure_boot to allow UART3 to be used in the non_secure area. However, as soon as I try to initialize it in the non_secure area a hard failure occurs...
Hello! I took the example of "usbd_cdc_acm" and added a receive and transmit buffer. The data from the receive buffer is sent back. It turned out that the first byte is written...
Hi All.
I have a project where my peripheral (nRF52832) connects to my central (nRF52840), and then transmits 128 byte packets continuously one after the other. It works...
We are using the nRF9160 DK with the Asset tracker example, which is working in combination with the nRF Cloud.
Now we want to use our own AWS account in combination with...
hi all i am trying to read data from a sensor in burst mode i can"t able to read all datas from the register .I tried to read the data in both spi and spim(with easydma) ...
Hello,
So I'm using nrf52832 with sdk15.2 and I'm trying to connect a joystick to the adc pins and have the joystick to move the mouse instead of the buttons and having...
hi.........
i am tried to merge the blinky and timer sample program , i am getting this error , even i have included all files .h , .c files
nrfx_config.h: No such file...
Hi
I am using nrf51822 chip to develop my application & I need to put the hardware into sleep. In which all the gpios & other peripheral goes stop to save power.
SO, how...
Hi,
I want to change MAC address during advertising in nrf52810.
nrf52810 receives MAC address via uart from other MCU and set this MAC address. (type is BLE_GAP_ADDR_TYPE_PUBLIC...
We're building small robots/toys that work with each other.
Would it be possible to use the nfct on two devices with nRF52840 to communicate between each other?
Also...
Hello,
I’m sorry for asking again, but I could need some help again. This is a followup to devzone.nordicsemi.com/.../missing-endcrypt-event.
I’ve managed to receive...
