I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, I have an issue with the watchdog and sd_app_evt_wait() when running the softdevice. It seems impossible to not let the watchdog go off while having an idle ble connection...
Hi there,
We're looking to improve the touch performance of our products by moving from PCB electrodes to a dedicated touch film. Can anyone provide any references to info...
Hello Nordic team,
What is the Maximum sampling frequency for i2s we can configure to nRf51 or nRF52 DK?
And if we enable UART module to print live of i2s on serial console...
Hi
I following the steps listed in the document Thingy Mesh Demo v0.1
https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
When i perform the step 5 "Open the...
Hello,
I am using sdk12.2.2 and nrf52 customized board. I want that user should be prompted to enter passkey before bonding. I refereed the code snippet from devzone and...
Hi!
Im using SDK14.2 and I m working with the custom characteristics tutorial(the one compatible with the SDK 14.2).I have an SDK5 device connected to a LORA radio with...
Hi,
I’m having some troubles writing into the fash memory. I work on KeilµVision.
I initialise flash doing :
uint32_t page_size = NRF_FICR->CODEPAGESIZE;
uint32_t...
I am adopting a project which was initiated by someone else. I am using GCC toolchain eclipse while previously used by other colleague who initiated the project used IAR....
Hi,
My product is automagically disconnected from the central after 9min of connection...
The same problem can be reproduced from the ble_app_template example as is, on...
Is it ok to execute the following program twice in succession when communicating data of 244 bytes or more with one communication?
do { err_code = ble_nus_data_send(&m_nus...
Hi Devzone,
I would like to print my payload on a hyperterminal using NRF_LOG_INFO().
My array is like that :
manufacturer_data [0] => Value: 0xAA; manufacturer_data...
Hi all!
I am approaching this with pretty much zero experience but what I'm trying to build should be a piece of cake for you so any help, example code, advice will be appreciated...
Hi Nordic,
I'm using nRF51, SDK 12 and softdevice version S130 to stream data from nrf51 to iphone6 over BLE.
Sometimes, Few hours after launching streaming, the BLE...
This is almost certainly a benign bug, but it doesn't hurt to point it out.
In nRF5_SDK_15.0.0_a53641a, nrf_drv_saadc_channel_init() is a macro that expands into a call...
