I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi ,
Here is my code used to write in to non volatile memory.
#include "nrf.h"
//#include "uicr_config.h"
#include <stdint.h>
#include <stdbool.h>
#include "nrf_nvmc...
hi,
i want to get the Email,MissedCall,Other(SMS) from Apple(ios7) to my device.
i survey that , ANCS(Apple Notification Center Service ) at the the Latest iOS7
and access...
Hi
I'm using the nrf51822 with Softdevice S110. I want to find out why a pairing has not worked, PIN-Code was wrong, PIN-Code timeout.
Which events I can use for that...
Hello,
I have tried the nRF51822 SDK example , "ble_app_hids_keyboard", it can send text "hello" to iPhone. When I cut off the power of the nRF51822 and turn it on again...
I have nRF8001-DK and Arduino Uno. ble_uart_project_template from nRF8001 SDK for Arduino (Bluetooth_low_energy_for_Arduino_0_5_0_0_RC2) was used. It was used with Master...
Hello,
i create a custom profile with two services and with 30 characteristics. The first service has 29 characteristics. Up to this point everything is ok, but when I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
Hi,
I have downloaded the new version of SDK (v.5.0) today and just tried your experimental ble_app_ancs (no modifications) but it seems it asserts with error_code=0xB...
Hi,
I need to know when to use the write_wo_resp property for a characteristics, and what is the difference between write and write_wo_resp property of a characteristics...
I've read a post from Marc Nicholas about the attempt to port the entire gcc toolchain under Xcode on Mac OS X.
As I wrote in another post, I've the entire gcc toolchain...
I'm getting started with this evaluation kit by working through the user guide and almost made it through the Blinky example before I ran into trouble.
After compiling...
