Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hi,
I have a problem with soft device. My code build well but when i try to compile it on nrf52840, i have below error:
Then i tried to go in boot loader:
Therefore...
Hi, Everyone
I have a product (named "A") developed on sdk12.3 and 52832.
This product has peripheral function and MTU Size is 64.
If I use "nRF Toolbox -> UART" on my smartphone...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello
I am using Segger Embedded Studio with nrf9160. I can 'Build and Run' the 'asset_tracker' project but the LEDs are not blinking and my development kit is not connecting...
Is possible to get a sample code for communication between multiple BLE devices, for example the BLE TinyShield? I have come across a code that enables the BLE TinyShield...
The content, format, and size of a device's Peer Data is determined by the application. I understand that when pm_peer_data_store() and there is not enough available flash...
Hello there,
In order to have a continuous RTT debug during DFU, I followed advices found in:
- https://devzone.nordicsemi.com/f/nordic-q-a/20708/rtt-logging-from-application...
Hi,
Apologies if this has been asked before. I am interested in trying out the Adafruit arduino implementation for the NRF52840. The implementation uses it's own bootloader...
