Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I played around with the UART demo on the nRF52-DK and the belonging Android apps nRF UART v2.0, nRF Connect and nRF Toolbox. On PC side I used a serial console...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 boarde and s210 soft device. My firmware makes use of sd_power_system_off(). If I have an update...
Hi guys
I'm trying to load the ble_app_beacon project on a custom board. I am able to flash the softdevice and the application, but the chip is not advertising. So, I started...
I've got the experimental ble blinky example project on an NRF52 PCA10040 working fine with an added custom characteristic. I can connect, discover and read/write characteristics...
Hi
I've implemented support for the FStorage and the FDS in our application. In some cases it happens, that the function "fds_stat" does not return.
The reason can be...
Hi,
Is it possible to reconfigure NFC pins to be GPIO inputs (and vice-versa) without any kind of reset? It seemed like some kind of soft reset was required when I looked...
I am trying to run the multilink central gcc example with s120 v2.1 on a nRF51822 CEAAD20 device. Unfortunately, SOFTDEVICE_HANDLER_INIT call causes a hard fault. The linker...
I'm trying to pass a string longer than 15 characters to NRFJPROG_rtt_write (it's 17 characters, including null-termination), but the data_written parameter is set to 15 after...
Hello everyone,
I am wondering that, can i find auto-connect feature on nrf chips? Firstly, i should match chip & device i know but after that can they match?
Second...
FWLog (1)_formattedByTC.txt Hi,
I am sending data to one of the characteristics from nRF51 to the App(the problem happens in both iOS and Android).
This is what I am observing...
Is there any documentation on the advertising state machine ? This post :
devzone.nordicsemi.com/.../
mentions the state machine and how it progresses from fast, to...
Hi all,
I want to update my connection parameter as follow:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) //400 /**< Minimum acceptable connection interval...
Hi,
I'm doing a project using the Evalution kit.
I don't know why, but I can't go under 350 uA current comsumption in system on.
I did clear all pins,i did NRF_SPI0-...
HI:
i use SPI is ok when i set frequency = NRF_DRV_SPI_FREQ_1M,but SPI will work abnormal when i set frequency = NRF_DRV_SPI_FREQ_500K/NRF_DRV_SPI_FREQ_250K/NRF_DRV_SPI_FREQ_125K...
