I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi..
i am using nrf52 and my custom made android application.
softdevice is 132.
in that am able to do DFU for application file with android master control panel.
i used...
Hi.
I will make clock.
I use RTC2 + Softdevice. (PCA10040 , NRF52832 , s132_nrf52_2.0.0_softdevice.hex )
Base Source code = nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral...
It seems to me that Nordic has implemented only a part of the Current Time Service.
I want to get the time zone in addition to the year, month, day, hour, minute, second...
Hi.
I'm developing firmware based on github.com/.../S130_LBS_client_server_central_peripheral example. I installed third party Softdevice s130, and with example of peripheral...
I have modifed the nus_uart(peripheral) to add static pass key in sdk 10.I used my mobile phone to test the functionality and it works as expected[asks for the passkey when...
Hi,
I'd like to put a BLE central in low power between two scan.
actually I use the example Ble_app_uart on a dk board PCA10028
and a second dk board as advertiser with...
Hi,
I am trying to get the SPI Slave working but was hoping to find a how-to. Is there an example of the SPI Slave for the S110 Soft Device (7.3.0)?
Currently, I am...
Hello,
I am developing custom HAL driver for SPI in NRF52 (PCA10040). The problem is that using the EasyDMA MAXCNT registers value must be between 1...255. It implicates...
Hi,
I am using nrf_pwm_noglitch.c from here . Is there a way to stop the pwm cleanly?. I would like to have a nrf_pwm_deinit(); similar to nrf_pwm_init(). Currently I set...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
About "ble_app_multilink_central" for the reference.
This code shows me below sequence.
Scan->connect request->get connection...
Hi,
We have an application where we have very very slow vcc risetime and therefore we have an external watchdog reset circuit connected to the -reset/swdio pin in order...
Hello,
the available QDID for nRF52x refers to Softdevice which has no IoT capability, being this a work in progress.
When this will be ready, will Nordic release a new...
Hi,
I want to use the NRF51822 without the Bluetooth functionality. Is it possible to leave the pins ANT1, ANT2 and VDD_PA unconnected? If no, what is the cheapest way...
