If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm trying to implement a HID gamepad on nRF52832. Here is my situation:
nRF is receiving frame over UART from master uC every 15 ms. Frame is being converted and...
I was trying to track down high, approx. 6mA, processor current consumption and I have found high current consumption if the FPU executes a divide by 0. If I comment out the...
When I start the "ble-sniffer_win_1.0.1_1111_Sniffer.exe" program I get this screenshot:
The port was found correctly (COM4) but I see no devices found.
Am I missing...
Which is more lower power consumption,system off mode or system reset (according to nReset/SWDIO pin Lo) when we don't use nRF51822 for a long time ?
Our products have...
Hello,
I have this code
if (NRF_SUCCESS!=nrf_drv_twi_tx(&m_twi,devAddr,®Addr,1,true))
return false;
unsigned int err_code = nrf_drv_twi_tx(&m_twi,devAddr,data...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I think "ble_app_hrs_rscs_relay" provides Central function and Peripheral function.
So it should be advertising right after running...
My program doesn't use SoftDevice.
In Reference Manual 3.0 page 52: "A HFCLKSTOP task will stop the HFCLK oscillator. However the HFCLKSTOP task can only be sent after...
Hi,
I've looked at the example codes provided by Martin in these two topics for communicating to a MPU6050 through TWI:
1- devzone.nordicsemi.com/.../ (uses SDK 9)
...
When we add a uuid will follow the steps below
err_code = sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type);
// Add the service.
err_code = sd_ble_gatts_service_add...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart" as reference.
As I've researching nRF51 with Central device,
it returns
Packet 0 : 020105 0c094e6f726469635f55415254...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
