Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hello, I want to create a simple example code with the leds ws2812b from neopixel from github.com/.../nrf51-neopixel. I need help to build the code.
Regards.
I'm converting an SDK 14.2.0 project to SDK 15.0.0 using the legacy functions and ARM GCC. It compiles OK but linking is failing.
The verbose output appears to be the Make...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
Hi,All,
I am using nrf52832 as a slave, the SDK version is 12.3. I set the connection timeout to 10s as follows
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(1000, UNIT_10_MS...
Hi,
I'm having an issue to connect a Galaxy samsung Tab A to my ble device.
Each time i ask for a connection i get the same error.
I already succeed with others phone...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
