Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hey,
We have a library (rust) responcible for communicating with the BLE peripheral Using btmgmt dbus messages to bluez.
We have never initiated a dedicated `aagent` in...
Hello All,
I am developing matter over thread based devices (Border router and End Devices) and for that I have chosen fanstel's MIG02C40F (nrf5340 + nRF7002) hardware...
Hello, Our board connects and remains connected to our server with only eDRX sleep periods. When a disconnect occurs we want to know if it's a connection issue to our server...
All examples from zephyr/samples/subsys/usb/audio don't work.
Both examples fail with the same message:
SDK version: 2.8.0 Board: PCA10175, revision 0.8.2
Is it expected...
Hi,
I´m developing a small ZigBee based sensor with Zephyr and the NCS and wondering how to add a remaining battery (%-based) attribute. The macro ZB_ZCL_DECLARE_POWER_CONFIG_ATTRIB_LIST...
Hello, sorry for disturb!
I meet build error as blow, how can I fix it? thx
BTW, I have installed zap tool manually( https://github.com/project-chip/zap/releases ),...
Hi,
I have a current leak on a new board.
I'm using a nrf52840.
My development environment is nRF Connect SDK v2.6.0.
I am using power management on I2C1.
When I...
Hello,
Currently, Nordic only provides an Android/IOS Application (Device Manager) for firmware update and other (Zephyr) functions.
For Windows, we currently rely on...
I am using the MESH distributor sample from the nRF Connect SDK (v2.8.0) on an nRF52840 development board. My aim is to use the RC oscillator (RC source) instead of the low...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello everyone, how are you? I
'm doing some communication tests between nRF52840 boards. I measure RSSI at different distances.
The problem is that in my tests, the RSSI...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
I am developing with the nRF5340 using NCS version 2.8 and want to test RSA 2048-bit encryption. However, there is only an example for 4096-bit encryption. Could you explain...