I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I'd like to know whether the cetnral get the data from peripheral or not. I'm using UART, it connects mcu(stm32f4) to ble module (nrf52832) and ble module gets the sensed...
I am having trouble understanding where am I going wrong . I am using the devacadamy sample with the BME280 sensor and just trying to get the device id for starters .
I am having a lot of trouble having to change my dt files and receive errors every time i try to run a basic sample for the NCS . Is there any 'How to' that i can refer and...
I hope to add custom data to the ASK package returned to TX in the ESB application. How can I add it in the input? How should the tx side read the custom data.
Hello,
I received the Thingy53 as part of the Hackster IO contest. Right now I am having problems to flash it through the VS Code. My VS Code instance is unable to detect...
I have a thingy 53 that I got from the HacksterIO competition, I'm trying to program it using the Programmer application from the NRF Connect Desktop application. I open Toolchain...
Hello,
I am trying to connect PS4 controller remote with NRF52840 so I can get command from remote and execute require action but not able to detect PS4 MAC in nRF52840...
Hi There,
I have been looking for ways to have three channels of a hardware timer with the NRF52840 generate a compare interrupt at different time intervals, my understanding...
I got MCUBoot running using signed images. Now I want to enable encrypted images using the build tools, but how? I've found this pull request: https://github.com/zephyrproject...
We are looking to move from STM32WB55 to Nordic.
I am use to developing firmware in the NXP and STM environments, looking at documentation for register address or examples...
I am trying to use the experimental task manager of the nrf52sdk, version 17.1.0. I've come across what I would call a bug, but there might be a reasoning behind it, so that...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
Hello everybody.
I am developing a BLE application in which I am using WDT every 12 seconds and a RTC interrupt every 10 seconds to send some information.
When you press...
Hi,
We are using nRF5340 and we are migrating to v2.0.2 NCS sdk from v1.9.1.
In our design, the SPI MISO pin is P0.10. From the dev zone tickets, I found that this P0...
Hi,
I'm trying to send I2S data (~ 16 kHz, 24 bits) via BLE using the nRF52 DK and the nRF5 SDK 17.1.0. After I get the data from the I2S driver (by specification, they...
