Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi Dev Team,
I had installed the newest NCS version NCS v1.6.1 and was importing my application from 1.5.1 to 1.6.1.
However, I noticed a lot of changes with respect to...
Hi,
I have a question ,According to the official tutorial，I succeeded BLE OTA DFU in windows system by nrfutil ,however, when I use the nrutil tool to update the firmware...
I have tried to use I2C but it does't work out. nRF9160 doesn't start booting after executing "build and run" and pushing the reset button.
I open secure_boot project...
Hi Nordic team
At sdk connect sample/mqtt_simple, it called lte_lc_init_and_connect() to connect NBIOT or LTE-M.
If this call was not successful, could we read error code...
hi support team,
very strange question from customer
customer set up one interrupt with following code:
void gpio_wakeup_init(void) { uint32_t err_code; if (!nrf_drv_gpiote_is_init...
Hello, I am routing the NRF52840-QIAA chip and wanted to avoid the costly via-in-pad process.
Can I use the following pins for QSPI quad mode?
Also can i leave the RESET...
I have a working set of implementations placed in the 17.0.2 SDK examples directory. The projects use SoftDevice s140 for BLE and flash write operations. I would like to know...
I'm looking to enable the flash protection for an nRF52 application running on Zephyr RTOS:
Basically looking to disable flash reads from the JTAG/SWD interface: Only...
Hello Nordic support,
I would like to understand regarding the status value 'ZB_ZDP_STATUS_NOT_SUPPORTED'.
I have a Zigbee application in which the device type is a Zigbee...
Hi,
I am using NRF52840 DK board. I am using SAADC example program for reading the voltage and SDK 15.3.0 Version.
We have connected the sensor to the adc analog output...
Hello Nordic team,
Our current setup:
nRF52840
nRF SDK v15.00
In our current setup, the steps we take are as following:
Initialize nRF52840 -> BLE fast advertisement...
I am developing a beacon for nRF52832 and can see the beacon in nRF Connect for iOS when using the following setting:
adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
I am implemeting serialisation using nRF52 as BLE PHY + STM32 micro as host with UART in between them.
I can see there is example for searilastion under "nrf5_SDK_for_Mesh_v5...
Hello
I want to test ncs ota function. b0 module following this link .
ncs1.6.0
borad:nrf52840dk_nrf52840
projece: ncs/zephyr/samples/hello_world
1. b0 + spm test...
